This article down below involving How to Install a Bathtub is highly motivating. Check it out for yourself and figure out what you think about it.
Setting up a bathtub isn't exactly rocket science, yet it does need solid plumbing, carpentry, and in some cases, tiling skills. Changing an old tub with a new one is also a reasonably tough project. If the old bathtub is conveniently easily accessible, the project can move easily; if you have to open up a wall surface to remove the old bathtub and also position the new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old bathtub and also set in the new one. Make certain you have qualified on your own for the task and fit attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is far better to think about using one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This post will assist you set up a brand-new tub in your bathroom if you have actually currently gotten a brand-new tub and also don't require to alter the setup of your previous supply of water pipes.
Your devices as well as product checklist should consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing taps can be rather troublesome due to the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers are in location between the tap as well as the sink. Protect the tap in place with the producer offered backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap ports. The former type should be connected to the tap finishes first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Making use of both wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the ideal supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used a minimum of when as this will resolve it into its last position.
Planning for the Installation
First of all, the sustaining framework provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent stress on the bathtub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a stiff seal, creating the water to pass through the wall between the bath as well as the tiling, causing difficulties with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is suggested to fit the tiles making use of waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub Yourself? Leave feedback down the page. We will be pleased to know your thinking about this write-up. In hopes that you visit us again soon. Feel free to take the opportunity to promote this blog if you liked it. I cherish reading our article about Tools You Need to Install a New Bathtub .
Go Deal Now